#N/A

#N/A

#N/A

DECA regulator / pressure controller with dual gauge for gas welding equipment, such as MIG/MAG and TIG. Suitable for use on an Argon/CO2 cylinder. Flow meter 0-30 l/min, 200 bar.

#N/A

#N/A

#N/A

MIGA 218 Welding machine
Manual wire feed welding (2-step)
Protected against overload
Equipped with Euro connection
4 welding programs

Included: Welding torch, welding cable 3 m, ground cable 2.7 m, gas hose 1.5 m

Technical data:
Power supply (Volt 50-60HZ) 1 Ph x 230
Fuse (AMP): 16A
Welding range:
MIG / No Gas: 10 – 180A
MMA: 10 – 150A
TIG: 10 – 180A
Duty cycle:
MIG / No Gas: (140A – 25%) – (90A – 60%)
MMA: (120A – 25%) – (85A – 60%)
TIG: (140A – 25%) – (90A – 60%)
No-load voltage (Volt): 86V
Coil: 100 – 200mm
Dimensions (L × W × H): 45 × 22 × 35 cm

Wire MIG MAN/SYN:
Steel: Ø0.6 – 0.8 – 0.9mm
Stainless steel: Ø0.8mm
Aluminium MG wire: Ø0.8 – 1.0mm
Aluminium Si wire: Ø0.8 – 1.0mm
CuSi 3 wire: Ø0.8m
CuSi 8 wire: Ø0.8mm
Shielded wire: Ø0.8 – 0.9 – 1.0 – 1.2mm

Electrodes:
Power supply (Volt 50-60HZ) 1 Ph x 230
Installation capacity: 3.5KW
Fuse (AMP): 16A
2-step wire feed
Euro coupling
Cable: 25mm²
Rutile: Ø1.6 – 3.2mm
Base welding electrodes: Ø2.0 – 3.2mm TIG torch electrode: Ø0.5 – 2.4mm

MIGA 220 Welding machine
Manual wire feed welding (2-step)
Protected against overload
Equipped with Euro connection
4 welding programs

Included: Welding torch, welding cable 3 m, ground cable 2.7 m, gas hose 1.5 m

Technical data:
Power supply (Volt 50-60HZ) 1 Ph x 230
Fuse (AMP): 16A
Welding range:
MIG / No Gas: 10 – 180A
MMA: 10 – 150A
TIG: 10 – 180A
Duty cycle:
MIG / No Gas: (140A – 25%) – (90A – 60%)
MMA: (120A – 25%) – (85A – 60%)
TIG: (140A – 25%) – (90A – 60%)
No-load voltage (Volt): 86V
Coil: 100 – 200mm
Dimensions (L × W × H): 45 × 22 × 35 cm

Wire MIG MAN/SYN:
Steel: Ø0.6 – 0.8 – 0.9mm
Stainless steel: Ø0.8mm
Aluminium MG wire: Ø0.8 – 1.0mm
Aluminium Si wire: Ø0.8 – 1.0mm
CuSi 3 wire: Ø0.8m
CuSi 8 wire: Ø0.8mm
Shielded wire: Ø0.8 – 0.9 – 1.0 – 1.2mm

Electrodes:
Power supply (Volt 50-60HZ) 1 Ph x 230
Installation capacity: 3.5KW
Fuse (AMP): 16A
2-step wire feed
Euro coupling
Cable: 25mm²
Rutile: Ø1.6 – 3.2mm
Base welding electrodes: Ø2.0 – 3.2mm TIG torch electrode: Ø0.5 – 2.4mm

Manual wire feed welding (2-step)
Protects against overload
Equipped with Euro connection
4 Welding programs

Included: Welding torch, welding cable 3 m, ground cable 2.7 m, gas hose 1.5 m

Technical data:
Power supply (Volt 50-60HZ) 1 Ph x 230
Fuse (AMP): 20A
Welding range:
MIG / No Gas: 10 – 200A
MMA: 10 – 160A
TIG: 10 – 200A
Duty cycle:
MIG / No Gas: (180A – 25%) – (100A – 60%)
MMA: (150A – 25%) – (100A – 60%)
TIG: (180A – 25%) – (100A – 60%)
No-load voltage (Volt): 86V
Coil: 200 – 300mm
Dimensions (L × W × H): 55 × 28 × 43 cm

Wire MIG MAN/SYN:
Steel: Ø0.6 – 0.8 – 0.9 – 1.0mm
Stainless steel: Ø0.8 – 1.0mm
Aluminium MG wire: Ø0.8 – 1.0 – 1.2mm
Aluminium Si wire: Ø0.8 – 1.0 – 1.2mm
CuSi 3 wire: Ø0.8 – 1.0mm
CuSi 8 wire: Ø0.8 – 1.0mm
Shielded wire: Ø0.8 – 0.9 – 1.0 – 1.2mm

Electrodes:
Power supply (Volt 50-60HZ) 1 Ph x 230
Installation power: 5KW
Fuse (AMP): 20A
2-step wire feed
Euro coupling Cable: 25mm² Rutile: Ø1.6 – 4.0mm Basic welding electrodes: Ø2.0 – 4.0mm TIG torch electrode: Ø0.5 – 2.4mm

DECA Spotter SW28 is a real all-rounder! Suitable for welding any type of metal (except aluminum).

Microprocessor
Power time setting
Single, Pulse or continuous spot selection
Gun with Quick release connection
Thermally protected Indicator

Data:

Power supply: 1 Ph x 230 V - 50/60 Hz
Fuse: 25 Amp
Circuit voltage: 2.4 – 7.4V in 50 steps
Welding current: ( I RMS ) = 250 – 2800A
( I2 MAX ) = 4500A
Cable length: 200cm + 300cm
Dimensions: 50 × 28 × 35 cm

#N/A